Samson MPL 1640 Specifications download pdf (Page 21)

Using Equalization

One of the most exciting aspects to using a mixer such as the MPL 1640 is hav-

ing the ability to shape a sound, using a process called equalization. But there

are few areas of sound engineering more misunderstood than equalization, and,

just as good EQ can really help a sound, bad EQ can really hurt it, so read on...

Every naturally occurring sound consists of a broad range of pitches, or frequen-

cies, combined together in a unique way. This blend is what gives every sound

its distinctive tonal color. The EQ section in a mixer allows you to alter a sound

by boosting or attenuating specific frequency areas. The MPL 1640 provides

independent three-band equalization controls for each of its sixteen channels.

The “High” knob affects frequencies in the 10 kHz area; the “Mid” knob affects

frequencies in the 800 Hz area; and the “Low” knob affects frequencies in the

80 Hz area. Each EQ knob is labeled with the maximum amount of cut or boost

provided (±15 dB in the case of high and low frequencies, and ±12 dB in the

case of the mid frequency).

We provided these particular frequency areas because they have maximum

impact on musical signals—that’s why they are sometimes known as “sweet

spots.” When an EQ knob is in its center detented position (“0”), it is having no

effect. When it is moved right of center, the particular frequency area is being

boosted; when it is moved left of center, the frequency area is being attenuated.

The high and low EQ controls employ what is known as a shelving curve (where

frequencies either above or below the specified area are affected, respectively)

while the mid frequency control employs what is known as a bell curve (where

frequencies both above and below the specified area are affected).

In most instances, the best way to approach equalization is to think in terms of

which frequency areas you need to attenuate, as opposed to which ones you

need to boost (boosting a frequency area also has the effect of boosting the

overall signal; too much EQ boost can actually cause overload—with the accom-

panying Peak LED warning!). Be aware of the phenomenon of masking, where

loud sounds in one frequency range obscure softer sounds in the same range;

by cutting EQ “notches” in a loud signal, you can actually make room for a softer

one to shine through. And try not to think of EQ as a miracle worker—no amount

of equalization can put a singer in tune or remove the distortion from an over-

loaded input signal! The key is to get the signal right in the first place, by using

correct gain structure and mic placement.

Although the specific EQ you will apply to a signal is very much a matter of

personal taste, here are a few general suggestions: Boosting the low frequency

of instruments such as bass drums or bass guitar will add warmth and make the

sound “fatter”; conversely, you may want to attenuate the low frequency compo-

nent of instruments such as cymbals, high-hats, and shakers so as to “thin” them

out. The mid-range control is particularly effective for vocals—attenuating it can

give a vocal performance more of an “FM-radio” feel, while boosting it can help a

vocal cut through dense instrumentation. Be careful not to boost high frequen-

cies too much or you risk adding hiss to the signal, though just a touch can help

add “shimmer” to an acoustic guitar, ride cymbal, or high-hat. Finally, because

both the high and low EQ settings are shelving controls, you can use them to

reduce hiss (by attenuating high frequencies) or rumble (by attenuating low

frequencies).

-15

+15

HIGH

-12

+12

MID

-15

+15

LOW

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 33 34

Comments to this Manuals

No comments

Samson MPL 1640 Specifications Page 21

Comments to this Manuals

Related products and manuals for Audio mixers Samson MPL 1640